Developer's Daily | Unix by Example |
main | java | perl | unix | dev directory | web log |
wvlan_cs ? Lucent WaveLAN/IEEE 802.11 device driver |
insmod wvlan_cs.o [irq_list=i,j,...] [port_type=n] [station_name=s] [network_name=s] [channel=n] [ap_density=n] [medium_reservation=n] [frag_threshold=n] [transmit_rate=n] [eth=n] [mtu=n] |
wvlan_cs is the low-level Card Services driver for the Lucent WaveLAN/IEEE 802.11 and compatible (the NCR WaveLAN/IEEE 802.11, the Cabletron RoamAbout 802.11 DS, the Melco WLI-PCM-L11) wireless ethernet adapters. When this driver is attached to a card, it allocates the next available device (eth0..eth#). This device name will be passed on to cardmgr(8) for the card configuration, and reported in the kernel log. |
irq_list=i,j,... |
Specifies the set of interrupts that may be allocated by this driver. |
port_type=n |
Select WaveLAN port type: [1] BSS - Basic Service Set (default), [2] WDS - Wireless Distribution System, [3] Pseudo-IBSS - ad-hoc network (no AccessPoint, PtP). |
station_name=s |
Sets the station name. The default is card-configured. |
network_name=s |
Sets the independent network name in ad-hoc mode. Sets the desired network (desired ESSID) to connect to if using an access point. The default is card-configured. |
channel=n |
Channel (frequency) for ad-hoc networks and is useless if using an access point. Valid range: [0-14] (depends on local restrictions) and defaults to [3] |
ap_density=n |
Sets the access point density (sensitivity). This affects modem and roaming thresholds. [1] low density (default), [2] medium density, [3] high density. |
medium_reservation=n |
Sets the medium reservation (RTS/CTS frame length), which affects the number of octets in a message or fragment above which a RTS/CTS handshake is performed. [500] hidden stations, [2347] no RTS/CTS (default). Valid range: [0-2347] |
frag_threshold=n |
Defines the number of bytes used for the fragmentation boundary for directed messages (Fragmentation length unicast message transmission). [2346] is the default, valid range: [256-2346] (even numbers only!). |
transmit_rate=n |
Transmit rate control. [1] fixed low, [2] fixed high, [3] auto select high (default), [4] fixed medium, [5] fixed high, [6] auto select standard, [7] auto select medium. |
eth=n |
Network device naming. By default [1] devices are named eth#, set this to [0] to have devices named wvlan#. |
||
mtu=n |
Maximum transfer unit. [1500] is the default, valid range: [256-2296] |
Use iwconfig(8) to manipulate wireless extensions. You need a kernel which was compiled with CONFIG_NET_RADIO set. It is recommended that you run at least Linux kernel 2.2.11 and use wireless_tools 19. Older version do not support all of the current commands. |
ESSID (network ID) |
Set the network ID of the desired network to connect to (with access point) or the name of your private ad-hoc network (no access point). |
Mode |
Set the operating mode to Ad-Hoc or Managed. In managed mode, the card will try to connect to an Access Point, to get access to the infrastructure. In Ad-Hoc mode, the card doesn’t require an Access Point and can communicate directly with its peers. |
Frequency & channels |
Channel (frequency) for ad-hoc networks. The frequency is
changed immediately and is only changeable in ad-hoc network
mode. You may enter a frequency value in the 2.4 GHz band or
the channel number. |
Sens |
Set the Access Point density (sensitivity). This affects modem and roaming thresholds. [1] low density (default), [2] medium density, [3] high density. |
Rts |
Sets the medium reservation threshold (RTS/CTS frame
length), which affects the number of octets in a message or
fragment above which a RTS/CTS handshake is performed. |
Frag |
Defines the number of bytes used for the fragmentation
boundary for directed messages (Fragmentation length unicast
message transmission). To be used when you have interference
on the radio, because it significantly decreases the
performance. |
Rate |
Set the rate used for transmission (but not reception).
You may want to set it to a fixed value for high number of
nodes. |
Enc |
Set the encryption key [0 to FFFF-FFFF-FF].
Use [off] and [on] to disable and reenable the
hardware encryption. This feature works only for device with
encryption option (Silver or Gold). |
Nick (station name) |
Set the station name (only used for debugging purpose). |
Statistics spy |
Set a list of MAC addresses in the driver (up to 8) and get the last quality of link for each of those (see iwspy(8)). |
/proc/net/wireless |
status is the status reported by the modem. Level and Noise refer to the signal level and noise level in dBm. |
You may use iwpriv(8) to manipulate private ioctls. |
Histogram |
This functionality allow to set a number of signal level intervals and to count the number of packets received in each of those defined intervals. This distribution might be used to calculate the mean value and standard deviation of the signal level. |
Some of the mentioned features are optional. You may enable to disable them by changing flags in the driver header and recompile. It’s currently not possible to use the WaveLAN/IEEE as a bridge (MAC level). This is not a restriction of the driver, the NIC firmware doesn’t allow to send out packets with another source MAC address than its own (which is mandatory required for bridgeing to work). Also the WaveLAN/IEEE can be used to connect to an Access Point, but cannot be an Access Point itself (because lack of bridgeing). |
Andreas Neuhaus <andy@fasta.fh-dortmund.de> |
I would like to thank Lucent Technology for making the necessary information available to public. Thanks to Nico Valster and Jan Martejin at Lucent for technical support. Thanks to Frank Bruegmann, who managed to get additional hardware for me so that I can now do tests in different environments. And thanks to Jean Tourrilhes for many patches and wireless kernel extensions. Also many thanks to everybody who tested and helped me developing this driver :-) |
cardmgr(8), pcmcia(5), ifconfig(8), insmod(1), iwconfig(8), iwspy(8), iwpriv(8). |